Skip to content
Water Softener Installation in Exeter, CA
Scheduled service Water Quality & Wells

Hard water, measured first

Water Softener Installation in Exeter, CA

The shower glass is cloudy again three days after you scrubbed it.

That white film is calcium and magnesium from the City's groundwater, the same minerals settling in your water heater. We test your tap, size a softener to the number we find, and answer the sodium question before anything is installed.

Response
Free hardness test, install usually within 2–3 days
Pricing
Agreed before we start
Licensed
CSLB #1072777
Rated
4.9 Google

What is it doing right now?

Describe the symptom. You get a real diagnosis and a price range back, not a call-out fee to find out.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

Sound familiar?

You are probably here because of one of these.

  • White, chalky rings on shower glass and tile that reappear within days of cleaning
  • Cloudy spots on glasses straight out of the dishwasher, even with rinse aid in the dispenser
  • A crust forming in the showerhead holes until the spray starts shooting off sideways
  • Soap that barely lathers and leaves a dull grey ring around the tub after every bath
  • A popping, rumbling noise from the water heater each time the burner heats a fresh tank
What is really going on

The problem underneath the symptom

01

The shower door is never clear, however hard you scrub

Every time hard water dries on glass, tile or chrome it leaves its minerals behind as a thin white layer. Clean it and it is back within days, because the source is the water itself. Cleaners that dissolve it also wear the finish, so after a few years the glass looks hazy even when it is clean.

02

The water heater gets louder every year

Hardness minerals come out of solution fastest when water is heated, so a tank water heater slowly fills with scale on its bottom. Water trapped under that layer flashes to steam as the burner fires, which is the popping and rumbling you hear, and the scale also stands between the flame and the water you are paying to heat.

03

A sales pitch that does not match your water

Some pitches lean on scary talk about minerals in general, or quote an oversized unit without testing anything. Exeter's water has a specific, measurable problem, which is hardness, and a moderate level of dissolved solids overall. A softener sized to what is actually coming out of your tap will do the job without paying for capacity you will never use.

What the City’s report actually says about Exeter hardness

Exeter’s tap water comes from the City’s own groundwater wells, and the City publishes what is in it every year. On hardness, the 2025 Consumer Confidence Report gives an average of 160 milligrams per liter, with a range of 110 to 230, from a sample dated June 28, 2022.

Softener makers work in grains per gallon, and one grain is 17.1 milligrams per liter. Converted, Exeter’s average is about 9.3 grains, and the range runs from about 6.4 to about 13.4. On the U.S. Geological Survey’s scale, 121 to 180 milligrams per liter counts as hard and anything above 180 as very hard. So the average is hard, and depending on the well the water runs from moderately hard at the low end to very hard at the top.

Two things are worth taking from that. First, there is no single Exeter number. The City draws from several wells, and the report shows them varying. Second, Exeter water is not high in total dissolved solids. The same report puts TDS at an average of 388 milligrams per liter, well under the 1,000 aesthetic standard. If someone says you need a softener because the water is “full of minerals” in general, they are describing a different town. Hardness is the specific issue here, and it is a real one.

Where the hardness ends up in your house

Hardness is mostly calcium and magnesium travelling with bicarbonate. The City’s report lists calcium averaging 41.2 milligrams per liter and magnesium 12.88 in 2025 samples, with bicarbonate averaging 195 in 2022. That combination forms calcium carbonate scale, and it forms faster once the water is heated.

So the hot places suffer first. A tank water heater collects scale across its bottom, where it insulates the water from the burner and starts to pop and rumble. A tankless unit’s narrow heat exchanger loses flow as scale lines it. After those come the places you can see: crust in showerhead holes, white rings on glass, spots on dishes, and faucet and shower cartridges that turn stiff.

A softener stops most of that at the source. It does not undo scale already inside a tank, so if your heater is noisy now, flushing the tank is still worth doing once the softener is running.

Sizing a softener to the water at your tap

We do not size from the citywide average. We test hardness at a cold tap in your house, then work out how many grains the softener has to remove each day from that reading and your household’s water use. That number sets the resin capacity. Too small and the unit regenerates constantly, burning through salt and water. Too large and the resin sits idle for long stretches between regenerations.

Because the City’s range runs from about 6 to about 13 grains, we leave headroom above the reading on the day. We also size for flow. The City’s water page says household pressure should usually sit between 35 and 50 psi, so a softener with a restrictive valve can make a shower feel weak whenever the washer is filling too.

On the plumbing side, we fit a bypass valve so the unit can be isolated, keep hose bibs and irrigation on hard water so you are not softening the lawn, and run the regeneration drain through an air gap as the plumbing code requires. If your garage already has a softener loop, the tie-in is simpler. A demand-initiated control, which regenerates on measured use rather than a fixed calendar, usually uses less salt and less water.

The sodium question

An ion exchange softener swaps hardness minerals for sodium. The more hardness it removes, the more sodium it adds. In Exeter that starts from a baseline the City already reports: sodium averaged 47.6 milligrams per liter in 2025, ranging from 35 to 63, before any softener touches it. Softened water here will carry more than that.

For most households this is not a concern. If anyone in your home has been told to watch sodium, ask your doctor, and consider what we can build in: potassium chloride in place of salt, a separate unsoftened cold line to the kitchen sink, or a reverse osmosis tap for drinking water.

When a softener is not the answer

A softener deals with hardness and nothing else. It does not touch the chlorine the City adds at its wells, so if taste or smell is your complaint, look at carbon filtration for the whole house instead. If you rent, ask the owner before any change to the main line. And if you only want to slow scale in a water heater without changing how the water feels, a salt-free conditioner is an option. It will not remove hardness or end spotting, but it can reduce how much scale sticks to hot surfaces. We will tell you plainly which of these fits your house.

Getting your Exeter water tested

All Flow Plumbing is based in Exeter, licensed under CSLB #1072777, bonded and insured. We test your hardness at the tap, explain what the reading means, and give you a written price for a softener sized to it before anything is installed. That price does not change unless you approve a change.

Call (559) 648-6871 to book a hardness test at your home.

How it goes

From your call to a working water softener installation

  1. 1

    Test hardness at your tap

    We measure hardness at a cold tap in your home, look for iron staining or sand in fixture screens, and ask about household size and water use, instead of relying on a citywide average.

  2. 2

    Size it in grains per day

    Measured hardness times daily water use gives the grains the softener must remove each day. From that we pick a resin capacity and a valve that keeps flow up, with headroom for the harder end of the City's range.

  3. 3

    Plan the tie-in

    We decide between an existing softener loop and cutting into the main line, fit a bypass valve, keep outdoor taps on hard water, add a sediment prefilter where sand is a concern, and route the drain through an air gap.

  4. 4

    Install, program and walk you through it

    We set the measured hardness into the control, choose demand-initiated regeneration where the unit offers it, load salt or potassium chloride, and show you the bypass and how to check the brine tank.

  5. 5

    Retest after it settles in

    Once the softener has been through its first regenerations we test the softened water at a tap again, confirm it reads close to zero hardness, and adjust the settings if it does not.

Local knowledge

Hard by the USGS yardstick, and the range matters as much as the average

The City of Exeter's 2025 Consumer Confidence Report lists hardness averaging 160 mg/L with a range of 110 to 230 mg/L, from a sample dated June 28, 2022. Softeners are rated in grains per gallon, and at 17.1 mg/L to the grain that is about 9.3 grains on average and roughly 6.4 to 13.4 across the range. The U.S. Geological Survey counts 121 to 180 mg/L as hard and anything above 180 as very hard, so the average is hard and individual wells run from moderately hard to very hard. The report also names the minerals doing it, calcium averaging 41.2 mg/L and magnesium 12.88 mg/L in 2025 samples, carried with bicarbonate averaging 195 mg/L. Sodium is already 47.6 mg/L on average before any softener, and total dissolved solids average a moderate 388 mg/L. That is a clear brief for a softener here: size it to a measured number with headroom, and plan for sodium from the start.

Exeter, CA Free hardness test, install usually within 2–3 days CSLB #1072777
Water Softener Installation in Exeter, CA. All Flow Plumbing technician installing a water softener tank
Water Softener Installation · Exeter, California
FAQ

Questions people actually ask

Straight answers about water softener installation in Exeter, no hedging, no upsell.

How much does a water softener cost to install in Exeter?

The price follows from things we measure rather than guess. The capacity your measured hardness and water use call for, whether there is already a softener loop or the main line has to be cut in, where the drain and power outlet sit, and extras such as an unsoftened kitchen line or a sediment prefilter. We test first and give you the exact price in writing, and it does not change unless you approve something different.

How soon can a softener go in at my Exeter home?

Because we are based in Exeter, the hardness test is easy to fit in, and installation usually follows within two to three days of it. A home with an existing softener loop in the garage is the quickest, because the tie-in is already there. Cutting into the main line takes a little longer, and we tell you which situation you have during the test.

Is Exeter's city water hard enough to need a softener?

By the USGS scale it is hard. The City's 2025 report gives an average of 160 mg/L from a 2022 sample, about 9.3 grains per gallon, within a range of 110 to 230 mg/L, which is moderately hard to very hard depending on the well. Whether you want a softener is your call. If scale on fixtures, glass and the water heater bothers you, a softener deals with it. If it does not, you can live without one.

Why does the City's water report give a hardness range instead of one number?

Exeter's water comes from several City wells, and their water is not identical. The 2025 Consumer Confidence Report lists hardness from 110 to 230 mg/L around an average of 160, sampled June 28, 2022. Your tap may not match the average on any given day, which is why we measure hardness in your home before sizing anything and leave headroom for the harder end of the range.

Will a softener add sodium to my drinking water?

Yes. An ion exchange softener trades hardness minerals for sodium, so softened water carries more than it started with. The City reports sodium in Exeter water already averaging 47.6 mg/L in 2025, before any softening. If sodium is a concern for anyone at home, talk to your doctor, and ask us about potassium chloride, a separate unsoftened kitchen line, or a reverse osmosis tap.

Will a softener get rid of the chlorine taste in Exeter water?

No. The City adds chlorine at its wells as a disinfectant, and a softener only exchanges hardness minerals. Chlorine taste and odor are handled by activated carbon filtration, either for the whole house or at the kitchen tap. A carbon filter and a softener can work side by side, but if taste is your only complaint, start with the filter and skip the softener.

Do salt-free water conditioners work on Exeter water?

They work differently. A salt-free conditioner does not remove calcium or magnesium, so the water stays hard by any test, glasses still spot and soap behaves the same. What a good one can do is change how the minerals behave so less scale sticks to heated surfaces such as a water heater. If you want genuinely soft water, it has to be ion exchange.

Still reading?

It will not fix itself, and it will not get cheaper.

Ten minutes on the phone usually tells you whether this is a small repair or a real project. That call costs nothing, and you get a real answer either way.

Reviewed by Jim Smith, Licensed Plumbing Contractor · Updated October 2026

Get a straight answer, fast

Tell us what is happening. We reply with a real diagnosis and a price range, usually within the hour.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

(559) 648-6871 Book