Skip to content
Water Heater Maintenance in Exeter, CA
Scheduled service Water Heaters

Planned water heater care

Water Heater Maintenance in Exeter, CA

That crackling under your water heater is rock forming in the bottom of the tank.

Exeter's City water carries calcium, magnesium and the odd grain of sand into your heater. A yearly flush and a proper safety check keep that layer thin, before it costs you hot water or a tank.

Response
Scheduled, usually within 2–4 days
Pricing
Agreed before we start
Licensed
CSLB #1072777
Rated
4.9 Google

What is it doing right now?

Describe the symptom. You get a real diagnosis and a price range back, not a call-out fee to find out.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

Sound familiar?

You are probably here because of one of these.

  • A rumble or sharp crackle from the tank a few seconds after the burner lights
  • Hot water at the kitchen tap that smells faintly of rotten eggs while the cold side smells normal
  • Grit like fine sand left in the bottom of the bathtub after filling it with hot water
  • Showers turning lukewarm sooner than they did last year with the same people in the house
  • A crusty white collar of mineral around the drain valve or the fittings on top of the tank
  • A small puddle or rust streak under the end of the relief valve discharge pipe
What is really going on

The problem underneath the symptom

01

The tank sounds like a pot of popcorn

When scale and sand cover the bottom of a gas tank, water gets trapped underneath and flashes to steam each time the burner fires. That is the popping. It also means the flame is heating a mineral crust before it heats your water, so the burner runs longer for the same shower.

02

Hot water runs out halfway through the second shower

Sediment takes up space that used to hold water, and on an electric heater it can bury the lower element completely. The tank still works, it just delivers less than its label says. Plenty of families blame a bigger household when the real cause is a tank slowly filling with mineral.

03

Nobody has touched it since the day it went in

Many heaters in Exeter garages have never been flushed, never had the anode looked at and never had the relief valve lifted. Everything seems fine until the drain valve will not open, the relief valve starts to weep, or the steel lining rusts from the inside where nobody can see it.

The sound in the garage, explained

Most people find out their water heater needs attention by ear. The burner clicks on, and a few seconds later the tank starts to crackle, tick or rumble like a kettle about to boil. It is louder at night when the house is quiet, and it tends to get worse over a couple of years rather than all at once.

That noise has a simple cause. A layer of loose grit and hard mineral has settled on the bottom of the tank, right where the flame (or the lower element on an electric unit) delivers its heat. Water seeps into pockets under that layer, flashes to steam and bursts up through it. Each burst is a pop.

The noise itself is harmless. What it tells you is not. The burner is heating a crust before it heats your water, the tank holds less than it used to, and the steel bottom is running hotter than it was designed to. Left long enough, that is how a tank that should have aged slowly ends up leaking from underneath.

Reading Exeter’s water report as a tank owner

In Exeter you do not have to guess what that crust is made of. Tap water in town comes from the City’s own wells, and the City’s 2025 Consumer Confidence Report lists the minerals one by one:

  • Calcium averaged 41.2 mg/L in 2025 sampling, ranging from 33 to 54.
  • Magnesium averaged 12.88 mg/L, ranging from 7.9 to 19.
  • Bicarbonate averaged 195 mg/L in 2022 sampling, ranging from 120 to 290.

The City’s water plan, citing the state, describes the groundwater under Exeter as generally a calcium bicarbonate type. That is precisely the chemistry that scales a water heater. Bicarbonate stays dissolved in cold water. Heat it and it releases carbon dioxide and becomes carbonate, which pairs with the calcium and falls out as a solid. A tank keeping forty or fifty gallons hot around the clock is doing that every hour of the day.

Taken together, the same report puts total hardness at an average of 160 mg/L, roughly 9 grains per gallon, from a 2022 sample. The range runs from 110 to 230 mg/L, so depending on the source the water is moderately hard to very hard. The report does not say which well’s water reaches a given house, so we plan maintenance around the harder end.

There is a second ingredient. The City’s Water Division says sand can occur naturally in groundwater or show up after a water line repair, and that it carries no health concern. Sand is heavier than water, so whatever slips past your faucet aerators settles in the one place in the house where water sits still and warm. Scale and sand together pack into a denser layer than either would form alone.

What a maintenance visit actually covers

We work through the heater in the same order every time, because the safety items come before the flush.

  1. Fuel, venting and straps. The gas connector and shutoff, the draft hood and flue on a gas unit, the wiring on an electric one, and whether the earthquake straps are still tight to the wall.
  2. The relief valve. We lift it to confirm it opens and reseats, and check that the discharge pipe ends where it should.
  3. The flush. Fuel or power off, a hose on the drain valve, then repeated cold-water rinses until the outflow runs clear.
  4. The anode rod. Where the fitting allows, we pull it and show you how much metal is left.
  5. Settings and a note. Thermostat checked, temperature measured at a tap, and a short written summary.

Tankless units get a different routine: isolation valves closed, a descaling solution pumped through the heat exchanger, and the inlet screen cleaned, since that screen is where sand tends to catch. If you are weighing one up, our page on tankless heaters for Exeter homes covers the upkeep honestly.

You may not need us for this

A straight answer: if your heater is fairly new, the drain valve works and you are comfortable shutting off gas or power, flushing a tank is a reasonable job to do yourself. Let the water cool first, run the hose somewhere the discharge cannot burn anyone or scorch a lawn, and open the cold supply in bursts to stir the bottom.

Calling makes sense when the drain valve is plastic and brittle, the tank has gone years without a flush, the relief valve has never been tested, or you want someone to look at the venting and the anode while the tank is empty. Those are the parts people skip, and they decide how long a tank lasts.

If you are tired of rinsing out grit and scale every year, a softener sized to Exeter’s hardness slows the scale side of it. It does nothing about sand, so the tank still needs an occasional flush.

When maintenance is no longer the answer

Flushing helps a tank that is sound. It cannot rescue one that is failing. Skip the maintenance visit and ask for a repair visit if you notice:

  • Water seeping from the tank body or from under the jacket, not from a fitting
  • Rusty water from the hot side only
  • A relief valve that keeps dripping after it has been tested
  • A burner that will not stay lit, or an electric unit that trips its breaker

Those point to diagnosing a failing heater, and sometimes to replacement. We will tell you which, and we will not flush a tank we expect to leak the week after.

Booking a flush in Exeter

All Flow Plumbing is based right here in Exeter, and maintenance is booked at a time that suits you. We look before we work, and the price is in writing before anything starts. We are licensed (CSLB #1072777), bonded and insured, and have been looking after Exeter homes since 2021.

Call (559) 648-6871 and tell us roughly how old the heater is, whether it is gas or electric, and what you have been hearing. That is enough to plan the visit.

How it goes

From your call to a working water heater maintenance

  1. 1

    Safety basics before anything else

    Before draining anything we look at the gas connection, the venting, the earthquake straps and the temperature and pressure relief valve. A unit with a bad vent or a seized valve needs that fixed first, and we will tell you so plainly.

  2. 2

    Drain and flush the sediment

    Fuel or power goes off, a hose goes on the drain valve to a safe spot, and we rinse with fresh cold water in short bursts until it runs clear. On a heavily scaled tank we stir the layer with repeated fills rather than forcing it.

  3. 3

    Pull and judge the anode rod

    The anode is a metal rod that corrodes on purpose so the tank lining does not. Where the fitting allows, we pull it and hand it to you. If it is down to bare wire, replacing it is a much smaller job than replacing the tank it protects.

  4. 4

    Test, refill and relight

    We lift the relief valve to confirm it opens and reseats, refill with a hot tap open so trapped air escapes, restore power or relight the burner, and measure the temperature at a faucet. You get a short written note on what we found.

Local knowledge

What the City's water report says is settling in your tank

Exeter's tap water comes from the City's own wells in the Kaweah Subbasin, and the City's 2025 Consumer Confidence Report names the minerals that matter to a water heater. Calcium averaged 41.2 mg/L and magnesium 12.88 mg/L in 2025 sampling, and bicarbonate averaged 195 mg/L in 2022 sampling, with some sources running well above those averages. The City's water plan describes the subbasin's groundwater as generally a calcium bicarbonate type. Heat is what turns that chemistry into a problem. Warm bicarbonate water gives up carbon dioxide, and the calcium drops out as calcium carbonate, the white crust you find on an old drain valve. A tank that holds water hot all day is a steady scale-maker. Add the sand the City says can occur naturally in its groundwater or arrive after a water line repair, and the bottom of an Exeter tank collects both mineral and grit. That combination is why a yearly flush here is ordinary upkeep rather than an extra.

Exeter, CA Scheduled, usually within 2–4 days CSLB #1072777
Water Heater Maintenance in Exeter, CA. All Flow Plumbing technician flushing sediment from a tank water heater
Water Heater Maintenance · Exeter, California
FAQ

Questions people actually ask

Straight answers about water heater maintenance in Exeter, no hedging, no upsell.

How much does water heater maintenance cost in Exeter?

It depends on what the heater is and what we find. Tank or tankless, gas or electric, whether the drain valve and anode fitting cooperate, how much sediment has built up, and whether an anode or relief valve needs replacing all change the job. We look at the heater first and give you the price in writing before we begin. It stays put unless you approve a change.

How often should I flush a water heater on Exeter City water?

Once a year is a sensible baseline. The City's 2025 Consumer Confidence Report puts hardness at an average of 160 mg/L, about 9 grains per gallon, from a 2022 sample, with a range of 110 to 230 mg/L, which is hard on the USGS scale. Large households or tanks set hotter may justify flushing more often. A softener slows scale but does not stop sand.

How soon can you come out to flush a water heater in Exeter?

Maintenance is a booked visit, usually within a few days, and since All Flow Plumbing is based in Exeter it is easy to fit around your schedule. If the tank is leaking, the burner will not light or you have no hot water at all, that is a repair call, not maintenance. Say so when you phone and we treat it as same-day work.

The City says Exeter water can contain sand. Does that end up in my water heater?

It can. The City's Water Division says sand can occur naturally in its groundwater or after a water line repair, that it is not a health concern, and that a persistent problem should be reported to the Water Division. Sand is heavier than water, so whatever passes your aerators settles in the tank and mixes with scale. Flushing is how it gets out.

Is it too late to flush a water heater that has never been drained?

Sometimes. On an older tank that has gone many years without a flush, the sediment can harden, and a brittle plastic drain valve may not close properly once it has been opened. We check the valve and the tank first. If the heater is near the end of its life, we will tell you a flush is not worth it and talk through repair or replacement instead.

Does a tankless water heater in Exeter need maintenance too?

Yes, though it looks different. Instead of draining a tank, we isolate the unit, circulate a descaling solution through the heat exchanger and clean the inlet screen, which is where sand tends to catch. Hard water scales a heat exchanger in much the same way it scales the bottom of a tank, so skipping it shortens the unit's working life.

What temperature should my water heater be set to?

Around 120 F is the common recommendation for most homes. It lowers the risk of scalding, especially for young children and older adults, and hotter water drops scale faster, so a lower setting also slows buildup in the tank. If someone in the house has a specific medical or dishwasher requirement, we can talk through the tradeoffs when we visit.

Still reading?

It will not fix itself, and it will not get cheaper.

Ten minutes on the phone usually tells you whether this is a small repair or a real project. That call costs nothing, and you get a real answer either way.

Reviewed by Jim Smith, Licensed Plumbing Contractor · Updated October 2026

Get a straight answer, fast

Tell us what is happening. We reply with a real diagnosis and a price range, usually within the hour.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

(559) 648-6871 Book