What the toilet is telling you before it quits
Most toilet trouble announces itself weeks ahead. The useful skill is knowing which noise or wobble means what, because each one has a different fix and a different level of urgency.
A hiss or trickle between flushes. Water is leaking from the tank into the bowl, usually past a worn or warped flapper, and the fill valve keeps topping the tank back up. To confirm it, put a few drops of food coloring in the tank, wait twenty minutes without flushing, and look in the bowl. Color in the bowl means the tank is leaking down.
It refills on its own every so often. That is the same leak, only slower. People call it a ghost flush. It is not an emergency, but it runs day and night until someone stops it.
It rocks when you sit on it. The bolts at the base have loosened, or the flange under the toilet is cracked or sits too low. A rocking toilet eventually crushes the wax ring that seals it to the drain. Once that seal breaks, water leaves with every flush and goes into the floor.
Water on the floor. Work out where it starts. Condensation sweating off the tank on a humid day looks different from a drip at the supply connection, and both look different from a slow seep at the base. Dry everything with a towel, flush, and watch.
The bowl fills high and drains slowly. That is a blockage in the toilet’s trapway or further down the pipe. One successful plunge is fine. If it keeps returning, or a tub gurgles when you flush, the restriction is past the toilet, and a clogged drain repair is what you need, not a new toilet.
You do not need us for a flapper. It is a hardware store part you can swap in a few minutes with the water off. Call us when a new flapper did not stop it, when the toilet moves, when there is water at the base, or when the valve behind it will not turn.
Repair or replace: how we help you decide
We price the repair first, because most toilets are worth fixing. Porcelain does not wear out. The parts inside the tank do, and they cost little next to a whole new toilet.
Replacement starts to make sense in a handful of situations:
- The tank or bowl is cracked, even a hairline crack, because those only grow
- It uses more than 1.6 gallons per flush and you are selling, remodeling, or tired of the water use
- It clogs constantly because of a narrow trapway, a known weakness of some early low-flow designs
- Parts for that model are no longer made, so every repair becomes a workaround
When we quote, you see both numbers in writing and decide. If the supply valve behind the tank is seized or crusted solid, we will point it out, because a new shutoff valve is often worth fitting while the toilet is already disconnected.
The 1.6 gallon line in Exeter’s older houses
The state’s fixture-efficiency statute, SB 407, sits in the Civil Code at sections 1101.1 to 1101.8. It reaches every house that was finished and usable by January 1, 1994. For toilets the test is simple: a bowl that takes more than 1.6 gallons to flush is out of compliance.
The statute leaves owners with three duties. Single-family homeowners had until January 1, 2017 to make the swap. Anyone selling has to tell the buyer about the rule and say whether the house still holds noncompliant fixtures. And a permitted alteration or improvement to a single-family house only gets its final approval once those fixtures have been changed.
In Exeter that covers most of the town. Census estimates put about 2,349 of the city’s 3,515 housing units as built before 1990, so at least two-thirds of the local housing stock falls under the law before you even count homes finished between 1990 and 1993.
What it means in practice:
- Selling an older Exeter home? Know what is in every bathroom before the disclosure forms arrive. A pre-sale plumbing inspection covers the toilets along with everything else.
- Planning a permitted remodel? Put every toilet, showerhead and tap in the scope from day one, because final approval depends on them.
- Neither? Then it is your call. We will tell you the rating and leave the decision with you.
Most toilets have their flush volume molded into the china just behind the hinge, or printed inside the tank. A reading of 3.5 or higher is well over the line.
What Exeter’s hard water does inside a tank
The City of Exeter’s 2025 water quality report lists hardness averaging 160 mg/L, from a sample taken in June 2022, with a range of 110 to 230 mg/L depending on the well. That is roughly 9 grains per gallon on average, which puts the town’s water in the hard category.
A toilet tank holds that water still for hours at a time. The minerals settle wherever water squeezes through a tight opening: the fill valve’s inlet screen, the seat the flapper closes against, and the row of rim holes that rinse the bowl. A crusted seat is why a brand-new flapper sometimes still leaks. Blocked rim holes are why a bowl starts flushing weakly and leaving streaks down the sides.
We scrape the seat and clear the rim holes while we are in there, which often restores a tired toilet without new parts. If scale keeps coming back across the house, it may be worth asking whether a water softener makes sense for you.
Getting an Exeter toilet fixed today
All Flow Plumbing is based in Exeter, so a toilet call in town is close to home. Repairs are normally done the same day. A replacement is usually set the next day, after we measure the rough-in and you choose a model that fits.
The phone is answered 24/7, weekends and holidays included. If a toilet is overflowing in the middle of the night, we tell you the after-hours rate on the call, before anyone drives over. Our licensed techs work under CSLB #1072777, bonded and insured, and the price you approve in writing is the price you pay.
Ring (559) 648-6871 to get a licensed tech headed your way.