Skip to content
Tankless Water Heaters in Exeter, CA
Same-day available Water Heaters

Tankless repair and installs

Tankless Water Heaters in Exeter, CA

The shower runs hot, then cold, then hot again, and the little screen on the wall is blinking a code.

Tankless units are compact and efficient, but Exeter's hard water coats their heat exchangers faster than most owners expect. We fix the fault in front of you and set up a descaling plan so it stays fixed.

Response
Same day for no-hot-water calls
Pricing
Agreed before we start
Licensed
CSLB #1072777
Rated
4.9 Google

What is it doing right now?

Describe the symptom. You get a real diagnosis and a price range back, not a call-out fee to find out.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

Sound familiar?

You are probably here because of one of these.

  • A code on the display that reappears a few days after every reset
  • Water that never gets as hot as it used to, even at the top setting
  • Hot water flow at the shower noticeably weaker than the cold side
  • A whistle or faint kettle-like hiss from the unit when the burner lights
  • White, chalky flakes caught in the inlet filter screen on the cold side
  • Temperature swings mid-shower while the handle stays in one position
What is really going on

The problem underneath the symptom

01

Error codes that clear and then come back

Power-cycling the unit brings the hot water back for a day or a week, then the same code returns. Scale faults behave exactly like this, because a restart does nothing about the mineral coating that is making the heat exchanger overheat or the flow sensor misread what is passing through it.

02

Cold bursts in the middle of a steady shower

A brief cold slug after someone shuts the tap and turns it back on is normal for many tankless models. Repeated swings while the water runs steadily are not. They usually point to restricted flow, a clogged inlet screen, or a burner that keeps backing off because the exchanger is running too hot.

03

It was sold to you as maintenance-free

Nobody mentioned service valves, a flushing kit or a schedule when the unit went on the wall. A tankless heater on hard water needs periodic descaling, and an install without isolation valves makes that job slower and messier than it has to be.

Same fault, different day

Tankless owners tend to call us after the third or fourth reset. The unit beeps, a code appears on the front panel, someone switches it off and on, and the hot water comes back. A week later it happens again, usually during the busiest shower of the morning.

A repeating code is information, not bad luck. Most tankless heaters log their recent faults, and the pattern says a lot. Ignition failures point one way, overheat and flow faults another. On hard water, overheat and flow codes are often the heat exchanger reporting that it is coated on the inside and can no longer shed heat into the water fast enough. Resetting clears the message. It does nothing about the scale.

That is why a tankless visit starts with the fault history, the gas pressure, the water flow and the inlet screen. The repair follows the cause.

Exeter’s hardness, translated for a heat exchanger

The City of Exeter publishes its water chemistry every year, and the figures explain a lot about tankless trouble in town. The 2025 Consumer Confidence Report puts hardness at 160 mg/L on average, with results from 110 to 230 mg/L (sampled in 2022). In the grains-per-gallon units most water heater manuals use, that is about 9.3 typically, and roughly 6.4 to 13.4 across the range. The USGS calls the average hard, and the upper end very hard.

The report also names what the hardness is made of. Calcium averaged 41.2 mg/L and magnesium 12.88 mg/L in 2025 samples, and bicarbonate averaged 195 mg/L in 2022. Heat that water and the calcium and bicarbonate come out together as calcium carbonate, the same white crust you see inside a kettle.

A tank heater spreads that crust across a broad bottom and keeps working, noisily, for a long time. A tankless unit has no such margin. It forces water through narrow passages in a compact heat exchanger and raises the temperature sharply in seconds. Scale builds where the heat is most intense, and even a thin layer narrows the passage and insulates the metal. The unit reacts by overheating, throttling the burner, or shutting down with a code. On Exeter water this is not a defect in your particular unit. It is chemistry, and it calls for a plan.

A descaling plan that fits your house

How often a tankless heater needs descaling depends on two things: how hard the water reaching it is, and how much hot water the household pulls through it. Because Exeter’s wells span moderately hard to very hard, one schedule for the whole town would be guesswork. We start from the manufacturer’s hard-water guidance, then adjust after the first service based on what actually comes out of the exchanger.

A workable plan has three parts:

  1. Service valves on the unit. Isolation valves on the hot and cold connections let us close off the heater and circulate descaler without draining the house. If your install lacks them, adding a set is usually the first improvement we suggest.
  2. A clean inlet screen. The small filter on the cold inlet catches grit and loose scale flakes. When it clogs, flow drops and the unit may refuse to fire.
  3. Less scale coming in. A whole-house softener or a scale-reduction cartridge ahead of the heater stretches the time between descaling visits considerably. It does not end the need altogether.

If you would rather have descaling handled on a routine schedule alongside any other heaters in the house, our Exeter water heater maintenance visits cover tankless units too.

Before you trade a tank for tankless

Tankless heaters deliver hot water for as long as you run it, free up the floor a tank occupies, and burn fuel only when a tap is open. Those are real advantages. So are the trade-offs, and you should hear them before the install rather than after.

  • Gas supply. A gas tankless burner draws far more gas while it fires than a tank burner. Many older homes need a larger or rerouted line, which we size by measuring pipe diameter, run length and every other appliance sharing it. That work falls under our gas piping services.
  • Venting. The old tank’s flue usually cannot be reused. Condensing units vent through plastic pipe and need a condensate drain, while non-condensing units need stainless venting.
  • Small draws. Tankless units need a minimum flow before they fire, so a trickle at the bathroom sink may stay cold.
  • Upkeep. On Exeter water, descaling is simply part of ownership.

If your current tank is young and working, there is no reason to replace it early. We would say so.

Mounted to the wall, not strapped like a tank

California’s water heater bracing statute, Health and Safety Code 19211, applies to standard heaters of 120 gallons or less for which a pre-engineered strapping kit is readily available. That language describes a storage tank, so a wall-hung tankless unit sits outside the tank strapping rule. Instead it is fastened to solid framing following the manufacturer’s instructions and the Plumbing Code, with its gas, water and vent connections supported so none of them carry strain.

Pricing, and how to reach us

The cost depends on whether the job is a repair, a descale or a new install, and on what the house needs around the unit: service valves, gas line capacity, vent route and electrical. We diagnose or survey first, then give you a written price that holds unless you approve a change.

All Flow Plumbing is an Exeter company, owned by Jim Smith since 2021 and licensed under CSLB #1072777. For a tankless unit that has stopped heating, call (559) 648-6871. Same-day no-hot-water visits are standard in town, and someone answers 24/7.

How it goes

From your call to a working tankless water heaters

  1. 1

    Read the fault history

    Most tankless units store their recent error codes. We pull that history, check gas pressure and water flow, and inspect the venting and condensate line, so the repair targets the cause instead of whatever code happens to be on the screen today.

  2. 2

    Clear the inlet and flow path

    We close the isolation valves, take out and clean the inlet filter screen, and check the flow sensor. A restriction at this point produces many of the symptoms people blame on the burner or the control board.

  3. 3

    Descale the heat exchanger

    With the gas and power off, a small pump circulates a descaling solution approved for the unit through the heat exchanger until the scale dissolves. We then flush with clean water, restart, and compare the outlet temperature against the setting.

  4. 4

    Leave you with a schedule

    Based on what came out of the exchanger and how much hot water your household uses, we tell you how often the unit should be descaled and whether softening or a scale-reduction cartridge would stretch that interval.

Local knowledge

Why every tankless unit in Exeter needs a descaling plan

The City of Exeter's 2025 Consumer Confidence Report lists hardness averaging 160 mg/L, with results between 110 and 230 mg/L from a June 2022 sample. Converted to the grains per gallon most tankless manuals use, that is about 9.3 on average and roughly 6.4 to 13.4 across the range, depending on the well. The USGS scale calls the average hard and the top of the range very hard. The same report breaks hardness into its parts. Calcium averaged 41.2 mg/L and magnesium 12.88 mg/L in 2025 samples, and bicarbonate averaged 195 mg/L in 2022, which fits the calcium bicarbonate groundwater the City's water management plan describes for the subbasin. Heat that water and calcium and bicarbonate drop out together as calcium carbonate. A tank heater spreads that scale over a wide floor. A tankless unit pushes the same water through narrow heat exchanger passages at high temperature, so even a thin coating restricts flow and traps heat.

Exeter, CA Same day for no-hot-water calls CSLB #1072777
Tankless Water Heaters in Exeter, CA. All Flow Plumbing technician servicing a wall-mounted tankless water heater
Tankless Water Heaters · Exeter, California
FAQ

Questions people actually ask

Straight answers about tankless water heaters in Exeter, no hedging, no upsell.

How much does a tankless water heater cost in Exeter?

For an install, the price depends on the unit, whether your gas line can feed it, the vent route, electrical needs and where it mounts. For a repair or descale, it depends on what failed and how badly the exchanger is scaled. We survey or diagnose first and give you an exact figure in writing. It does not change unless you approve a change.

If my tankless stops working, how soon can you come out in Exeter?

No hot water is a same-day call for us. We are based in Exeter, so a house in town is a short trip from home base. If the unit is leaking we will come out at any hour, weekends and holidays included. A genuine late-night callout carries an after-hours rate, which we tell you on the phone before we head over.

How often should a tankless heater be descaled on Exeter water?

There is no single number for the whole city, because the City's own report shows hardness running from roughly 6 to 13 grains per gallon depending on the well, and every household uses a different amount of hot water. Start from your manufacturer's hard-water schedule, then adjust based on what the first descale shows. A busy household on the harder end will need it more often.

Does a tankless water heater need earthquake straps in California?

California's strapping statute, Health and Safety Code 19211, is written for standard tank water heaters of 120 gallons or less with a pre-engineered strapping kit available. A wall-hung tankless unit is not a freestanding tank, so that rule does not describe it. It is fastened to solid framing according to the manufacturer's instructions and the Plumbing Code instead.

Will a water softener help my tankless unit?

Usually, yes. A softener exchanges the calcium and magnesium that form scale, so far less of it builds inside the heat exchanger and descaling can happen less often. It does not remove the need for service entirely. Check the water quality section of your unit's manual, since manufacturers spell out the conditions they expect the heater to see.

Is it worth switching to tankless if my tank heater still works?

Often not right away. If your tank is young and healthy, replacing it early mostly trades a working appliance for new gas, venting and descaling needs. Tankless makes the most sense when the tank is near the end, when floor space matters, or when the household keeps running out of hot water. We will tell you honestly which camp you are in.

Can my existing gas line run a tankless heater?

Sometimes, but many cannot. A gas tankless burner draws much more gas while it fires than a tank burner does, and a line sized for an old tank and a furnace may starve it. We check pipe size, run length and every other gas appliance on the line before quoting, and include any upsizing in the written price.

Still reading?

It will not fix itself, and it will not get cheaper.

Ten minutes on the phone usually tells you whether this is a small repair or a real project. That call costs nothing, and you get a real answer either way.

Reviewed by Jim Smith, Licensed Plumbing Contractor · Updated October 2026

Get a straight answer, fast

Tell us what is happening. We reply with a real diagnosis and a price range, usually within the hour.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

(559) 648-6871 Book