Skip to content
Sewer Ejector Pumps in Exeter, CA
Emergency service Drains & Sewer

Sewage ejector pump repair

Sewer Ejector Pumps in Exeter, CA

The pump alarm is buzzing and the lowest shower drain has water standing in it.

When a fixture sits lower than the sewer line, a pump is the only thing moving its waste out of the house. In Exeter we answer around the clock and repair floats, check valves and pumps on the private side of the sewer.

Response
Answered live 24/7, often on site within the hour
Pricing
Agreed before we start
Licensed
CSLB #1072777
Rated
4.9 Google

What is it doing right now?

Describe the symptom. You get a real diagnosis and a price range back, not a call-out fee to find out.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

Sound familiar?

You are probably here because of one of these.

  • A buzzer or flashing light on the pump alarm panel, often in a closet or on an outside wall
  • The pump cycling on and off again and again when nobody is using any water
  • A loud thunk from the discharge pipe each time the pump shuts off
  • Dirty water creeping up through the floor drain or shower pan of the lowest room in the house
  • A sewer gas smell around the basin lid even after the room has been cleaned
  • A low hum from the basin with no sound of water moving
What is really going on

The problem underneath the symptom

01

An alarm nobody in the house understands

A buzzer goes off in a closet or a light starts flashing on a box mounted to the wall, and you realize you have never thought about the pump it belongs to. Maybe it came with the house. Nobody left instructions, and right now you do not know whether you can flush the toilet or run the shower.

02

The lowest room fills instead of draining

When the pump stops, the fixtures that depend on it have nowhere to send their waste. The next shower or flush rises back up through the lowest drain in that room, and it is raw sewage, not clean water. Every gallon run upstream of a dead pump makes the cleanup bigger.

03

A sewage smell with nothing visibly leaking

The room near the basin smells like a sewer, yet the floor is dry and the pump seems to run. A cracked lid gasket, a loose seal around a pipe or a vent that no longer does its job lets gas escape from a basin that is meant to be closed, and the odor will not clear until the seal does.

When the alarm goes off, do this first

A high-water alarm means the basin is filling faster than the pump is emptying it, or the pump has stopped altogether. The alarm is set to sound before the basin overflows, so you have a little margin, but not much.

  1. Stop running water anywhere that drains to the basin. If you are not sure which fixtures those are, hold off on all of them: no flushing, no showers, no laundry, no dishwasher.
  2. Silence the buzzer with the switch on the panel if it has one. That quiets the noise and fixes nothing, so leave the rest of the panel alone.
  3. Check the breaker for the pump circuit, and whether the pump plugs into an outlet that has tripped. Reset either one only if the floor around you is completely dry.
  4. Listen near the basin. A hum with no sound of water moving points to a jammed impeller or a closed valve. Silence points to power, the float switch or the motor.
  5. Leave the sealed lid on. The basin holds raw sewage and sewer gas, and nothing inside it is safe to handle with the lid off and the pump live.

Then call us. If the reset brought the pump back and it emptied the basin, call anyway. Whatever tripped it is likely to do it again.

Exeter’s sewer runs on pumps too

Most of the time, sewage moves by gravity. A pipe sloped downhill carries waste away from the house with no help at all. Gravity has one catch: it only works while there is somewhere lower to go.

The City of Exeter’s own system shows how far that catch reaches. Eight lift stations sit along the City’s collection network, which stretches past 36 miles of pipe between four inches and three feet wide. By the time it all arrives at the treatment plant, that is about 800,000 gallons a day, finished off in ponds where the treated water soaks into the ground or evaporates. On flat valley ground, a sewer that keeps sloping downward eventually sits too deep to build and maintain, so a lift station pumps the flow back up and lets it start falling again.

A house works on the same physics at a smaller scale. When a toilet, shower or washer sits lower than the point where the home’s drain line heads out to the sewer, its waste has nowhere lower to go. An ejector pump does for that room what a lift station does for a neighborhood. It collects the flow in a sealed basin and pushes it up to a height where gravity can take over.

Most Exeter homes drain entirely by gravity and will never need one. The ones that do usually have a room or an addition set below the main drain, or an outbuilding that sits lower than the line it ties into.

Your pump, your responsibility

The City looks after its lift stations. Your ejector is another matter. It sits on private property and feeds your own sewer connection, and section 13.12.060 of Exeter’s municipal code makes the owner the one who keeps laterals and connections working and pays to do it. It also leaves the owner answerable for harm that follows from neglect, which matters if a failed pump sends sewage into a tenant’s unit or a neighbor’s space.

In practice the pump deserves the attention you would give a water heater: a check now and then, an alarm that actually works, and a plan for when the power goes out. Private sewer work is done to the current California Plumbing Code, and we pull permits where the work requires them.

What is inside the basin, and what usually fails

An ejector system is a handful of parts, and each one fails in its own way.

  • The float switch tells the pump when to start and stop. Wipes, grease or a shifted pump can trap it, so the pump never starts or never stops.
  • The pump has an impeller built to pass solids, but rags, wipes and paper towels still wrap it until the motor hums and nothing moves. A motor that has been straining long enough eventually burns out.
  • The check valve on the discharge pipe keeps pumped sewage from falling back into the basin. When it fails, the pump moves the same water again and again and runs far more often than it should. A loud bang as the pump shuts off often comes from this valve.
  • The vent lets air in and gas out as the basin fills and empties. A blocked or missing vent means slow pumping and odors.
  • The lid and its gaskets keep the gas inside. A cracked gasket is a common reason a room smells of sewage with nothing leaking.
  • The alarm is the only warning you get. Plenty of older systems have one that has never been tested, or none at all.

Repair, replace, or rethink

A stuck float or a failed check valve is usually a repair. An old pump with a burned motor, or one undersized for the fixtures it serves, is usually a replacement, and that is the moment to add an alarm if there is none, fit a proper shutoff valve and confirm the vent works. If you are planning a new room below your drain line, talk to us before the layout is final, because the fixtures and the pump should be designed together as part of the plumbing for a bathroom addition.

An ejector is not a sump pump, and the two are not interchangeable. A sump pump moves groundwater and stormwater, while an ejector handles sewage. And if ordinary gravity drains elsewhere in the house are slow as well, the trouble may sit further down the line, where clearing the main drain comes first.

A full basin cannot wait until morning

If the alarm is sounding or the lowest drain is filling, call (559) 648-6871 at any hour. A live person answers, and our crew starts from right here in Exeter. Night work is billed at an after-hours rate that you hear before we roll, and the repair price is in writing before work begins. State license CSLB #1072777, bonded and insured.

How it goes

From your call to a working sewer ejector pumps

  1. 1

    Stop the inflow and make it safe

    Before we arrive, we ask you to stop using the fixtures that drain to the basin. On site we check the power safely and, if the basin is full, clear the jam or pump it down before anything else.

  2. 2

    Test the controls

    We lift the float through its range, test the alarm, check the circuit and outlet, and confirm the check valve and shutoff valve are working, so we know which part failed instead of guessing.

  3. 3

    Pull and inspect the pump

    With the power off and the line isolated, the pump comes out of the basin. We clear the impeller, check the motor, cord and seals, and look at what has been going down the drains that feed it.

  4. 4

    Repair or replace, then watch it cycle

    Once you approve the written price, we replace the failed part or the pump, reseal the lid and fill the basin. We then watch several full cycles, start to stop, before calling the job done.

Local knowledge

Even Exeter's City sewer needs 8 pumping stations

Exeter's public sewer is not a purely gravity system. The City's Wastewater Division keeps 8 lift stations running along a collection network longer than 36 miles, with pipe ranging from four inches up to three feet wide, and roughly 800,000 gallons a day reach its plant, where the treated water finishes in percolation and evaporation ponds. A town on flat valley ground cannot count on gravity the whole way, so the City pumps. A house with a fixture lower than its own drain line faces the same problem on a smaller scale, and a sewage ejector pump is its private lift station. The difference is who looks after it. The City maintains its 8 stations. Exeter's municipal code puts the upkeep of private sewer connections, and the cost of it, on the property owner, so a pump on your property feeding your connection is yours to maintain.

Exeter, CA Answered live 24/7, often on site within the hour CSLB #1072777
Sewer Ejector Pumps in Exeter, CA. All Flow Plumbing technician lifting an ejector pump out of its basin
Sewer Ejector Pumps · Exeter, California
FAQ

Questions people actually ask

Straight answers about sewer ejector pumps in Exeter, no hedging, no upsell.

How much does ejector pump repair or replacement cost in Exeter?

It turns on what failed and how easy it is to reach. A float or check valve is a smaller job than a burned-out pump, a grinder pump costs more to replace than a standard ejector, and a basin in a tight closet takes longer to work in. Adding a missing alarm or fixing a vent changes the scope too. We diagnose first, and the number we write down before starting is the number you pay unless you agree to a change.

My ejector pump alarm is going off at night in Exeter. How fast can you come?

A full basin is treated as an emergency, and a live person answers our phone at any hour. Our crew starts from right here in Exeter, so an address in town is a short trip. Real middle-of-the-night callouts are billed at an after-hours rate, which you hear up front so you can choose. Until we arrive, stop using every fixture that drains to the basin.

Does the City of Exeter maintain the ejector pump at my house?

No. The City runs the public collection system, its 8 lift stations included. A pump on your property that feeds your sewer connection is private equipment, and section 13.12.060 of the Exeter Municipal Code makes the owner responsible, practically and financially, for keeping private laterals and connections working. Repairs, replacement and any damage from a failure fall to the owner.

Do I need an ejector pump for a new bathroom in my Exeter home?

Only if the new fixtures sit lower than the drain line they have to tie into. Most bathrooms added at the main floor level drain by gravity like the rest of the house. If the room is below that line, you need a pumped system, either a sewage ejector with a basin or, for a single toilet, sometimes a compact macerating unit. We check the elevations before you settle the layout.

What is the difference between a sewage ejector pump and a sump pump?

A sump pump moves groundwater or stormwater that collects in a pit, and it usually discharges outside. A sewage ejector moves waste from toilets, showers and laundry into the sewer, through a sealed and vented basin built to handle solids. They are not interchangeable, and sewage should never go into a sump pit or out a sump discharge.

Can I use the toilet during a power outage if I have an ejector pump?

Only sparingly, and only fixtures that do not drain to the basin. The pump stops when the power does, and the basin has limited room before it backs up. Fixtures on gravity drains elsewhere in the house still work normally. If outages worry you, ask us about a battery-powered alarm or a backup option for the pump.

What should never go down a drain that feeds an ejector pump?

Wipes of any kind, including ones labelled flushable, paper towels, feminine products, dental floss and cooking grease. They wrap around the float and the impeller, and they are the most common reason we pull an ejector pump that has quit. Toilet paper and ordinary household waste are what the pump is built to handle.

Still reading?

It will not fix itself, and it will not get cheaper.

Ten minutes on the phone usually tells you whether this is a small repair or a real project. That call costs nothing, and you get a real answer either way.

Reviewed by Jim Smith, Licensed Plumbing Contractor · Updated October 2026

Get a straight answer, fast

Tell us what is happening. We reply with a real diagnosis and a price range, usually within the hour.

No obligation, no upfront fee. We will never sell your details.
In a genuine emergency, calling is faster: (559) 648-6871

(559) 648-6871 Book